I tuoi dati personali saranno trattati con assoluta riservatezza e non saranno trasmessi a terzi senza autorizzazione.

Stati Uniti

Cranchi 50'

323.117 € = 350.000 USD

Informazioni di base

Marchio: Cranchi
Modello: 50'
Paese: Stati Uniti
Città: Barrington, RI
Anno di costruzione: 2003
Tipologia barca: Diporto sportivo
Categoria: Barca motor

Larghezza (m): 4,27
Lunghezza (m): 15,24
Bozza (m): 0,91
Cuccette: 3

Descrizione

Waf1 Crew Yacht | 50' Cranchi 2003

(Major $49,000 Price Reduction August 5, 2023)

This 2003 Cranchi Mediterranée 50 has undergone significant updates, specifically in the last 12 months since the owner's purchase her in 2021. She is currently being stored indoors and can be viewed by appointment. This boat has an excellent layout. Below are a list of her features. Please read the description section for a full list of updates.

Three Stateroom & Two Head Layout

Twin Volvo D-12 Diesel Engines with Approximately 1,150 Hours

Fischer Panda Generator

Bow Thruster

Air Conditioning & Heating

Garmin & Raymarine Electronics

Hydraulic Tender Garage

Much More!

Waf1 Crew HIGHLIGHTS

Yacht Details 50' Cranchi 2003
Location Barrington, RI
Engines Volvo
Last Updated Jan 11, 2024
Asking Price $350,000
Cruising Speed
Maximum Speed
Max Draft 3' 5''

Updates

Change oil pump and filter
Replace coolant port and starboard engine
Straightline fabrication/interior bedding
replacement, exterior helm and cockpit
cushions, replacement of complete canvas
enclosure
NorEast marine/replace chiller system
Thru hulls – Replace engine generator
and chiller intake thru-hulls. Forespar
valves. New strainers and supply hoses
Dry fit engine intake valves. Float valve
and stem into epoxy, glue stem with
life-caulk. Antifouling coating. Replace
bonding wires on engine thru-hulls
Install general zincs exterior
Sand and paint bottom one coat
Volvo shift problem
Thru hulls – replace engine generator
and chiller intake thru-hulls. Forespar valves
cleaned all mounting surfaces. Dry fit
Forespar aft thru-hulls with backing pads
glue stem on the exterior with lifeseal
glue and float backing pads attached to
thru-hulls in place. Install new strainers
and supply hoses. Dry fit engine intake
valves, make backing plates. Float valve
and stem into epoxy, glue stem with
life-caulk. Strip away old paint on the
exterior, prime surface and apply antifouling coating. Replace bonding wires on
engine thru-hulls.
Install engine zincs
Change belts main engine
Repair bilge pump and shower sump
Repair fresh water leak in water system
Replace Crankcase and air filters main eng
Remove broken fitting Stbd Trans cooler
New docking fenders with covers & lines
Change fuel filters main engines
Replace broken trim cylinders/replace
trim pump and four trim cylinders
HeadSync toilet repair, bow seal, vac pump
Replace forward hatch
Compound and wax hull
Compound and wax cockpit
Touch up gel-coat starboard side
Air conditioning ducting – make access
panels for a/c ducting replacement
Replace additional ducting
NorEast marine/replace chiller system
Remove backs of seats onboard, remove
nose cone in engine room and cockpit
seating
Straightline fabrication/interior bedding
replacement, exterior helm and cockpit
cushions, replacement of complete
canvas enclosure
Cay electronics
Change fuel filters x 4
Install general zincs/exterior and internal
engine
Replace batteries
Change engine impeller
Service thruster
House bank battery charger
Charger generator battery
Battery cables and battery cable ends/
make new battery cable jumpers,
change cable ends
Generator; remove and rebuild by
Fischer Panda
Clean air intake filters
Build crate to ship generator
Paint bottom 2 coats
Compound and wax hull
Hull touch ups
House bank battery charger
Charger generator battery
Compound and wax superstructure
Hull touch ups
Remove old sea deck/wood not sealed
properly
Deck areas sand all surfaces, fill all holes